Point De Centre Dcl Definition

The term DCL refers to the luminaire connection device. We call the light points of DCL boxes, DCL boxes. These terms refer indistinctly to central boxes and wall sconces. – BBC central boxes for new buildings with a diameter of 68 mm. For the safety of the occupants of a house, each light circuit on the control panel must be protected as much as possible by a 16 A circuit breaker, which interrupts the power supply in case of overheating of electrical cables or short circuit. The wires used must have a cross-section of at least 1.5 mm². Finally, 8 light points can be assigned to the same circuit, but at least two circuits are required for each apartment with an area greater than 35 m². There are boxes with a diameter of 68 mm and boxes with a diameter of 85 mm. Commonly used central boxes are 68 mm diameter boxes o For ceiling lights, the following terms are used: central pot, DCL central pot, central box, DCL central box, central box, DCL central box, BBC central box. The lamp is hung on the hook screwed into the box. In new buildings, the gypsum box must support a load of 25 kg. For this reason, the central boxes are threaded on the back of the M6 box. For ceiling lights, we use a central housing and for wall sconces, a wall sconces housing.

We will not talk about the equipment for collective accommodation (Prefa boxes, DCL octopus boxes…), but only boxes with central and wall lamps that can be found in individual apartments or during renovations. Terms used to refer to wall lamps and middle boxes. – The boxes of the building center: They are not BBC and let air through. The main features and functions of the middle boxes and wall boxes were the main features and wall boxes. In a second step, find the desired location for the box and mark the center of the area to be drilled with a cross. Whether the wall is solid or hollow, check with a material detector that there are no pipes or metal parts in the area to be drilled. Yes. In particular, it has been mandatory for new buildings and renovations since 1 October 2001 according to standard NF C 15-100. Adjust the diameter of your bell saw (or drill, depending on the hardness of the wall) to match the diameter of your DCL box, then drill the ceiling wherever you want.

Then drill the ceiling frame (with a drill adapted to its nature) and screw the corresponding stud onto the threaded rod. Insert it into the hole and push it in. The luminaires can be supplied with a DCL socket or installed later. Connect the bare strands of the electrical wires to the terminal block quick connectors in the following order: A DCL connector has three flat pins aligned. The 8 mm long mass pin is located in the center of the phase and the neutral conductor, both 7 mm long and whose axes are spaced 15 mm apart. The grounding pin may be missing on DCL plugs (sockets), but remains present on all DCL sockets (sockets). Published: 2018-02-18 10:22:30 Categories: Power Supply Finally, hide excess cable in the surface cover of your fixture. All you have to do is fix your light bulb and get the power back on! Stop taking electrical risks: have your system checked by a specialist! Draw a mark on the threaded rod in alignment with the plasterboard, and then unscrew it.

Measure the depth of the box: you need to remove this distance from the previously indicated length on the threaded rod. Mark your second marker and place the rod in your miter box to saw it off after that second marker. Finally, screw the box attachment to the threaded rod, then insert the rod into the peg to the ceiling and make sure everything is tightened with the Allen wrench. o Boxes to be sealed: sealing of gypsum or prompt (quick-setting cement) – recessed diameter: 40 mm, 54 mm, 65 mm, 67/68 mm, 85 mm. There are reusable outlets that plug directly into a DCL outlet and allow you to install a construction lamp. If you have a wall lamp with a square base of 70 x 70 mm, you will not be able to repair the wall lamp if you use a box of wall sconces with a diameter of 68 m. And even with a wall lamp box with a diameter of 54 mm, we have little space. We will be forced to choose another wall lamp or a wall lamp of 40mm diameter, which will no longer be DCL or BBC. Until now, the connecting wires of wall and ceiling lights were found in a rudimentary junction box. The occupant of the apartment had to connect it to the luminaire via a screw terminal.

There could be a risk of electric shock if the person forgot to turn off the power. In addition, the installation could deteriorate after several manipulations, making it difficult to establish new connections[2]. Remove the wires enough to connect them more easily. For some situations, however, an exception may apply: DCL allows luminaires to be connected to a circuit. It`s a real take in reduced format. DCL is internationally standardized by IEC as IEC 61995[1]. Do you want to modernize your electrical installation or facilitate the replacement of your future lighting? Let`s see together how you can equip your home with integrated DCL bases. The DCL (Luminaire Connection Device) consists of a cover and a housing with a socket that allows the installation or replacement of a luminaire by simply connecting or disconnecting it. A true small socket, this device is compatible with all luminaires (its suspension system must be able to support a load of up to 25 kg) and ensures the electrical safety of new and old homes. Lower the intensity of your lights with a dimmer! As with any intervention in the power grid, disconnect the power supply at the subscriber circuit breaker (AGCP), upstream of the switchboard, and make sure that there is no voltage at the output of the supply lines with a current tester.

There are wired kits that can comply with this regulation. Collect the electrical wires coming out of the ceiling, then remove their ends by about 9 mm. DCL enclosures allow the electrical connection of ceiling lights and wall sconces. They meet safety standards, so you can change a bulb or fixture without having to touch the electrical cables. The electrical connector is located on the DCL cover and to power a ceiling light, simply use a DCL socket to wire the power supply to the ceiling light, or use a DCL socket with a bulb clamped directly into the DC cover. The DCL cover can accommodate the DCL plug or socket. All you have to do is attach the terminal block to the recessed box until it is locked and screw in the visible hook. If necessary, prepare a little plaster to fill the old hole in the ceiling. The hardest part is done! Once your box is recessed, follow these steps to install your lights and sockets in seconds: Read also: 👍 The NF C 15-100 standard, a safety guarantee for your electrical installation. Remove the pre-cut cable cover, put it in the box and install it on the ceiling to press its collar against the wall. Secure it firmly with the clips and fixing screws provided for this purpose so that the claws keep it drywall.